Inspecting /boot/System.map-2.6.22-rc4-49-default Loaded 26165 symbols from /boot/System.map-2.6.22-rc4-49-default. Symbols match kernel version 2.6.22. No module symbols loaded - kernel modules not enabled. klogd 1.4.1, log source = ksyslog started. <5>Linux version 2.6.22-rc4-49-default (geeko@buildhost) (gcc version 4.1.3 20070521 (prerelease) (SUSE Linux)) #1 SMP 2007/06/08 14:42:31 UTC <6>Command line: root=/dev/vg_system/root vga=0x317 resume=/dev/vg_system/swap maxcpus=4 report_lost_ticks mce=bootlog apic=debug <6>BIOS-provided physical RAM map: <4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) <4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) <4> BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) <4> BIOS-e820: 0000000000100000 - 00000000dfff0000 (usable) <4> BIOS-e820: 00000000dfff0000 - 00000000dfffe000 (ACPI data) <4> BIOS-e820: 00000000dfffe000 - 00000000e0000000 (ACPI NVS) <4> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) <4> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) <4> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) <4> BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved) <4> BIOS-e820: 0000000100000000 - 0000000220000000 (usable) <7>Entering add_active_range(0, 0, 159) 0 entries of 3200 used <7>Entering add_active_range(0, 256, 917488) 1 entries of 3200 used <7>Entering add_active_range(0, 1048576, 2228224) 2 entries of 3200 used <4>end_pfn_map = 2228224 <6>DMI 2.3 present. <4>ACPI: RSDP 000FA1B0, 0014 (r0 ACPIAM) <4>ACPI: RSDT DFFF0000, 0030 (r1 A M I OEMRSDT 4000710 MSFT 97) <4>ACPI: FACP DFFF0200, 0084 (r2 A M I OEMFACP 4000710 MSFT 97) <4>ACPI: DSDT DFFF0340, 566B (r1 1HQC8 1HQC8003 3 INTL 2002026) <4>ACPI: FACS DFFFE000, 0040 <4>ACPI: APIC DFFF0290, 00A4 (r1 A M I OEMAPIC 4000710 MSFT 97) <4>ACPI: OEMB DFFFE040, 0081 (r1 A M I AMI_OEM 4000710 MSFT 97) <6>Scanning NUMA topology in Northbridge 24 <6>Number of nodes 4 <3>Node 0 using interleaving mode 3/0 <6>No NUMA configuration found <6>Faking a node at 0000000000000000-0000000220000000 <7>Entering add_active_range(0, 0, 159) 0 entries of 3200 used <7>Entering add_active_range(0, 256, 917488) 1 entries of 3200 used <7>Entering add_active_range(0, 1048576, 2228224) 2 entries of 3200 used <6>Bootmem setup node 0 0000000000000000-0000000220000000 <4>Zone PFN ranges: <4> DMA 0 -> 4096 <4> DMA32 4096 -> 1048576 <4> Normal 1048576 -> 2228224 <4>early_node_map[3] active PFN ranges <4> 0: 0 -> 159 <4> 0: 256 -> 917488 <4> 0: 1048576 -> 2228224 <7>On node 0 totalpages: 2097039 <7> DMA zone: 56 pages used for memmap <7> DMA zone: 1224 pages reserved <7> DMA zone: 2719 pages, LIFO batch:0 <7> DMA32 zone: 14280 pages used for memmap <7> DMA32 zone: 899112 pages, LIFO batch:31 <7> Normal zone: 16128 pages used for memmap <7> Normal zone: 1163520 pages, LIFO batch:31 <6>Nvidia board detected. Ignoring ACPI timer override. <6>If you got timer trouble try acpi_use_timer_override <6>ACPI: PM-Timer IO Port: 0x4008 <7>ACPI: Local APIC address 0xfee00000 <6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) <6>Processor #0 (Bootup-CPU) <6>ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) <6>Processor #1 <6>ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) <6>Processor #2 <6>ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) <6>Processor #3 <6>ACPI: LAPIC (acpi_id[0x05] lapic_id[0x84] disabled) <6>ACPI: LAPIC (acpi_id[0x06] lapic_id[0x85] disabled) <6>ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled) <6>ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled) <6>ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) <6>IOAPIC[0]: apic_id 4, address 0xfec00000, GSI 0-23 <6>ACPI: IOAPIC (id[0x09] address[0xfeafe000] gsi_base[40]) <6>IOAPIC[1]: apic_id 9, address 0xfeafe000, GSI 40-46 <6>ACPI: IOAPIC (id[0x0a] address[0xfeaff000] gsi_base[47]) <6>IOAPIC[2]: apic_id 10, address 0xfeaff000, GSI 47-53 <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) <4>ACPI: BIOS IRQ0 pin2 override ignored. <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) <7>ACPI: IRQ9 used by override. <6>Setting APIC routing to flat <6>Using ACPI (MADT) for SMP configuration information <4>mapped APIC to ffffffffff5fd000 ( fee00000) <4>mapped IOAPIC to ffffffffff5fc000 (00000000fec00000) <4>mapped IOAPIC to ffffffffff5fb000 (00000000feafe000) <4>mapped IOAPIC to ffffffffff5fa000 (00000000feaff000) <4>swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 <4>swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e8000 <4>swsusp: Registered nosave memory region: 00000000000e8000 - 0000000000100000 <4>swsusp: Registered nosave memory region: 00000000dfff0000 - 00000000dfffe000 <4>swsusp: Registered nosave memory region: 00000000dfffe000 - 00000000e0000000 <4>swsusp: Registered nosave memory region: 00000000e0000000 - 00000000f0000000 <4>swsusp: Registered nosave memory region: 00000000f0000000 - 00000000fec00000 <4>swsusp: Registered nosave memory region: 00000000fec00000 - 00000000fec01000 <4>swsusp: Registered nosave memory region: 00000000fec01000 - 00000000fee00000 <4>swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fee01000 <4>swsusp: Registered nosave memory region: 00000000fee01000 - 00000000ff700000 <4>swsusp: Registered nosave memory region: 00000000ff700000 - 0000000100000000 <6>Allocating PCI resources starting at f1000000 (gap: f0000000:ec00000) <6>SMP: Allowing 8 CPUs, 4 hotplug CPUs <6>PERCPU: Allocating 50312 bytes of per cpu data <4>Built 1 zonelists. Total pages: 2065351 <5>Kernel command line: root=/dev/vg_system/root vga=0x317 resume=/dev/vg_system/swap maxcpus=4 report_lost_ticks mce=bootlog apic=debug <4>Initializing CPU#0 <4>PID hash table entries: 4096 (order: 12, 32768 bytes) <4>Marking TSC unstable due to TSCs unsynchronized <6>time.c: Detected 2600.033 MHz processor. <4>Console: colour dummy device 80x25 <4>Checking aperture... <4>CPU 0: aperture @ f8000000 size 64 MB <4>CPU 1: aperture @ f8000000 size 64 MB <4>CPU 2: aperture @ f8000000 size 64 MB <4>CPU 3: aperture @ f8000000 size 64 MB <4>Memory: 8257044k/8912896k available (2005k kernel code, 131112k reserved, 985k data, 312k init) <4>Calibrating delay using timer specific routine.. 5203.29 BogoMIPS (lpj=10406592) <6>Security Framework v1.0.0 initialized <4>Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) <4>Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) <4>Mount-cache hash table entries: 256 <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 1024K (64 bytes/line) <6>CPU 0/0 -> Node 0 <6>SMP alternatives: switching to UP code <6>ACPI: Core revision 20070126 <4>enabled ExtINT on CPU#0 <4>ESR value after enabling vector: 00000000, after 00000004 <4>ENABLING IO-APIC IRQs <4>Synchronizing Arb IDs. <7>init IO_APIC IRQs <7>IOAPIC[0]: Set routing entry (4-0 -> 0x30 -> IRQ 0 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-1 -> 0x31 -> IRQ 1 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-2 -> 0x32 -> IRQ 2 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-3 -> 0x33 -> IRQ 3 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-4 -> 0x34 -> IRQ 4 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-5 -> 0x35 -> IRQ 5 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-6 -> 0x36 -> IRQ 6 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-7 -> 0x37 -> IRQ 7 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-8 -> 0x38 -> IRQ 8 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-9 -> 0x39 -> IRQ 9 Mode:1 Active:0) <7>IOAPIC[0]: Set routing entry (4-10 -> 0x3a -> IRQ 10 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-11 -> 0x3b -> IRQ 11 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-12 -> 0x3c -> IRQ 12 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-13 -> 0x3d -> IRQ 13 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-14 -> 0x3e -> IRQ 14 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-15 -> 0x3f -> IRQ 15 Mode:0 Active:0) <7> IO-APIC (apicid-pin) 4-16, 4-17, 4-18, 4-19, 4-20, 4-21, 4-22, 4-23, 9-0, 9-1, 9-2, 9-3, 9-4, 9-5, 9-6, 10-0, 10-1, 10-2, 10-3, 10-4, 10-5, 10-6 not connected. <6>..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1 <6>Using local APIC timer interrupts. <4>result 12500177 <6>Detected 12.500 MHz APIC timer. <6>SMP alternatives: switching to SMP code <6>Booting processor 1/4 APIC 0x1 <4>Initializing CPU#1 <4>masked ExtINT on CPU#1 <4>Calibrating delay using timer specific routine.. 5200.43 BogoMIPS (lpj=10400869) <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 1024K (64 bytes/line) <6>CPU 1/1 -> Node 0 <4>AMD Opteron(tm) Processor 852 stepping 01 <6>SMP alternatives: switching to SMP code <6>Booting processor 2/4 APIC 0x2 <4>Initializing CPU#2 <4>masked ExtINT on CPU#2 <4>Calibrating delay using timer specific routine.. 5200.45 BogoMIPS (lpj=10400902) <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 1024K (64 bytes/line) <6>CPU 2/2 -> Node 0 <4>AMD Opteron(tm) Processor 852 stepping 01 <6>SMP alternatives: switching to SMP code <6>Booting processor 3/4 APIC 0x3 <4>Initializing CPU#3 <4>masked ExtINT on CPU#3 <4>Calibrating delay using timer specific routine.. 5200.42 BogoMIPS (lpj=10400840) <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 1024K (64 bytes/line) <6>CPU 3/3 -> Node 0 <4>AMD Opteron(tm) Processor 852 stepping 01 <6>Brought up 4 CPUs <4>migration_cost=583 <6>NET: Registered protocol family 16 <6>ACPI: bus type pci registered <6>PCI: Using configuration type 1 <6>ACPI: Interpreter enabled <6>ACPI: (supports S0 S1 S4 S5) <6>ACPI: Using IOAPIC for interrupt routing <6>ACPI: PCI Root Bridge [PCI0] (0000:00) <7>PCI: Probing PCI hardware (bus 00) <6>PCI: Transparent bridge - 0000:00:09.0 <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] <6>ACPI: PCI Root Bridge [PCIB] (0000:04) <7>PCI: Probing PCI hardware (bus 04) <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCIB.POGA._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCIB.POGB._PRT] <4>ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *9 <4>ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *9 <4>ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *10 <4>ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled. <4>ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled. <4>ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *5 <4>ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0, disabled. <4>ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *9 <4>ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *0, disabled. <4>ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *0, disabled. <4>ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled. <4>ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled. <4>ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *11 <4>ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *9 <4>ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *14 <6>Linux Plug and Play Support v0.97 (c) Adam Belay <6>pnp: PnP ACPI init <6>ACPI: bus type pnp registered <7>IOAPIC[0]: Set routing entry (4-8 -> 0x38 -> IRQ 8 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-13 -> 0x3d -> IRQ 13 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-4 -> 0x34 -> IRQ 4 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-3 -> 0x33 -> IRQ 3 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-7 -> 0x37 -> IRQ 7 Mode:0 Active:0) <7>IOAPIC[0]: Set routing entry (4-1 -> 0x31 -> IRQ 1 Mode:0 Active:0) <6>pnp: PnP ACPI: found 15 devices <6>ACPI: ACPI bus type pnp unregistered <6>PCI: Using ACPI for IRQ routing <6>PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report <7>number of MP IRQ sources: 16. <7>number of IO-APIC #4 registers: 24. <7>number of IO-APIC #9 registers: 7. <7>number of IO-APIC #10 registers: 7. <6>testing the IO APIC....................... <4> <7>IO APIC #4...... <7>.... register #00: 04000000 <7>....... : physical APIC id: 04 <7>.... register #01: 00170011 <7>....... : max redirection entries: 0017 <7>....... : PRQ implemented: 0 <7>....... : IO APIC version: 0011 <7>.... register #02: 04000000 <7>....... : arbitration: 04 <7>.... IRQ redirection table: <7> NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: <7> 00 00F 0 0 0 0 0 1 1 30 <7> 01 00F 0 0 0 0 0 1 1 31 <7> 02 00F 0 0 0 0 0 1 1 32 <7> 03 00F 0 0 0 0 0 1 1 33 <7> 04 00F 0 0 0 0 0 1 1 34 <7> 05 00F 1 0 0 0 0 1 1 35 <7> 06 00F 0 0 0 0 0 1 1 36 <7> 07 00F 0 0 0 0 0 1 1 37 <7> 08 00F 0 0 0 0 0 1 1 38 <7> 09 00F 0 1 0 0 0 1 1 39 <7> 0a 00F 1 0 0 0 0 1 1 3A <7> 0b 00F 1 0 0 0 0 1 1 3B <7> 0c 00F 0 0 0 0 0 1 1 3C <7> 0d 00F 0 0 0 0 0 1 1 3D <7> 0e 00F 0 0 0 0 0 1 1 3E <7> 0f 00F 0 0 0 0 0 1 1 3F <7> 10 000 1 0 0 0 0 0 0 00 <7> 11 000 1 0 0 0 0 0 0 00 <7> 12 000 1 0 0 0 0 0 0 00 <7> 13 000 1 0 0 0 0 0 0 00 <7> 14 000 1 0 0 0 0 0 0 00 <7> 15 000 1 0 0 0 0 0 0 00 <7> 16 000 1 0 0 0 0 0 0 00 <7> 17 000 1 0 0 0 0 0 0 00 <4> <7>IO APIC #9...... <7>.... register #00: 05000000 <7>....... : physical APIC id: 05 <7>.... register #01: 00060011 <7>....... : max redirection entries: 0006 <7>....... : PRQ implemented: 0 <7>....... : IO APIC version: 0011 <7>.... register #02: 00000000 <7>....... : arbitration: 00 <7>.... IRQ redirection table: <7> NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: <7> 00 000 1 0 0 0 0 0 0 00 <7> 01 000 1 0 0 0 0 0 0 00 <7> 02 000 1 0 0 0 0 0 0 00 <7> 03 000 1 0 0 0 0 0 0 00 <7> 04 000 1 0 0 0 0 0 0 00 <7> 05 000 1 0 0 0 0 0 0 00 <7> 06 000 1 0 0 0 0 0 0 00 <4> <7>IO APIC #10...... <7>.... register #00: 06000000 <7>....... : physical APIC id: 06 <7>.... register #01: 00060011 <7>....... : max redirection entries: 0006 <7>....... : PRQ implemented: 0 <7>....... : IO APIC version: 0011 <7>.... register #02: 00000000 <7>....... : arbitration: 00 <7>.... IRQ redirection table: <7> NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: <7> 00 000 1 0 0 0 0 0 0 00 <7> 01 000 1 0 0 0 0 0 0 00 <7> 02 000 1 0 0 0 0 0 0 00 <7> 03 000 1 0 0 0 0 0 0 00 <7> 04 000 1 0 0 0 0 0 0 00 <7> 05 000 1 0 0 0 0 0 0 00 <7> 06 000 1 0 0 0 0 0 0 00 <7>IRQ to pin mappings: <7>IRQ0 -> 0:0 <7>IRQ1 -> 0:1 <7>IRQ2 -> 0:2 <7>IRQ3 -> 0:3 <7>IRQ4 -> 0:4 <7>IRQ5 -> 0:5 <7>IRQ6 -> 0:6 <7>IRQ7 -> 0:7 <7>IRQ8 -> 0:8 <7>IRQ9 -> 0:9 <7>IRQ10 -> 0:10 <7>IRQ11 -> 0:11 <7>IRQ12 -> 0:12 <7>IRQ13 -> 0:13 <7>IRQ14 -> 0:14 <7>IRQ15 -> 0:15 <6>.................................... done. <6>PCI-DMA: Disabling AGP. <4>PCI-DMA: aperture base @ f8000000 size 65536 KB <6>PCI-DMA: using GART IOMMU. <6>PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture <4>ACPI: RTC can wake from S4 <6>pnp: 00:08: iomem range 0xffb80000-0xfffffffe could not be reserved <6>pnp: 00:08: iomem range 0xdfefc000-0xdfefcfff could not be reserved <6>pnp: 00:08: iomem range 0x0-0x0 could not be reserved <6>pnp: 00:08: iomem range 0x0-0x0 could not be reserved <6>pnp: 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved <6>pnp: 00:09: iomem range 0xfee00000-0xfeefffff could not be reserved <6>pnp: 00:0b: ioport range 0x680-0x6ff has been reserved <6>pnp: 00:0b: ioport range 0x295-0x296 has been reserved <6>pnp: 00:0b: ioport range 0x778-0x77f has been reserved <6>pnp: 00:0b: ioport range 0xb78-0xb7f has been reserved <6>pnp: 00:0b: ioport range 0xf78-0xf7f has been reserved <6>pnp: 00:0c: iomem range 0xe0000000-0xefffffff could not be reserved <6>pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved <6>pnp: 00:0d: iomem range 0xc0000-0xdffff has been reserved <6>pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved <6>pnp: 00:0d: iomem range 0x100000-0xdfffffff could not be reserved <6>PCI: Bridge: 0000:00:09.0 <6> IO window: b000-bfff <6> MEM window: fc600000-fe6fffff <6> PREFETCH window: f1000000-f10fffff <7>PCI: Setting latency timer of device 0000:00:09.0 to 64 <6>PCI: Bridge: 0000:04:01.0 <6> IO window: disabled. <6> MEM window: disabled. <6> PREFETCH window: disabled. <6>PCI: Bridge: 0000:04:02.0 <6> IO window: f000-ffff <6> MEM window: fe900000-fe9fffff <6> PREFETCH window: disabled. <6>NET: Registered protocol family 2 <6>Time: acpi_pm clocksource has been installed. <4>IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) <4>TCP established hash table entries: 1048576 (order: 12, 25165824 bytes) <4>TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) <6>TCP: Hash tables configured (established 1048576 bind 65536) <6>TCP reno registered <6>Unpacking initramfs... done <6>Freeing initrd memory: 3673k freed <6>audit: initializing netlink socket (disabled) <5>audit(1182955614.296:1): initialized <4>Total HugeTLB memory allocated, 0 <5>VFS: Disk quotas dquot_6.5.1 <4>Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>io scheduler noop registered <6>io scheduler anticipatory registered <6>io scheduler deadline registered <6>io scheduler cfq registered (default) <6>vesafb: framebuffer at 0xfd000000, mapped to 0xffffc20002780000, using 6144k, total 8128k <6>vesafb: mode is 1024x768x16, linelength=2048, pages=4 <6>vesafb: scrolling: redraw <6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 <6>bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 81749 bytes,<6>...found (1024x768, 46202 bytes, v3). <4>fbcon_del_cursor_timer:468: <4>Console: switching to colour frame buffer device 124x44 <6>fb0: VESA VGA frame buffer device <6>Real Time Clock Driver v1.12ac <6>Non-volatile memory driver v1.2 <6>Linux agpgart interface v0.102 (c) Dave Jones <6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled <6>00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A <6>PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 <4>PNP: PS/2 controller doesn't have AUX irq; using default 12 <6>serio: i8042 KBD port at 0x60,0x64 irq 1 <6>serio: i8042 AUX port at 0x60,0x64 irq 12 <6>mice: PS/2 mouse device common for all mice <6>input: AT Translated Set 2 keyboard as /class/input/input0 <6>input: PC Speaker as /class/input/input1 <6>NET: Registered protocol family 1 <6>Freeing unused kernel memory: 312k freed <6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 <6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <5>SCSI subsystem initialized <4>ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126] <4>ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126] <4>ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126] <4>ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126] <6>NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0 <6>NFORCE-CK804: chipset revision 242 <6>NFORCE-CK804: not 100% native mode: will probe irqs later <6>NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller <6> ide0: BM-DMA at 0x3000-0x3007, BIOS settings: hda:DMA, hdb:DMA <6> ide1: BM-DMA at 0x3008-0x300f, BIOS settings: hdc:DMA, hdd:DMA <7>Probing IDE interface ide0... <4>hdb: MATSHITADVD-ROM SR-8178, ATAPI CD/DVD-ROM drive <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 <7>Probing IDE interface ide1... <7>libata version 2.21 loaded. <7>sata_nv 0000:00:07.0: version 3.4 <4>ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22 <7>IOAPIC[0]: Set routing entry (4-22 -> 0x49 -> IRQ 22 Mode:1 Active:1) <6>ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 22 (level, low) -> IRQ 22 <5>sata_nv 0000:00:07.0: Using ADMA mode <7>PCI: Setting latency timer of device 0000:00:07.0 to 64 <6>scsi0 : sata_nv <6>scsi1 : sata_nv <6>ata1: SATA max UDMA/133 cmd 0xffffc2000273a480 ctl 0xffffc2000273a4a0 bmdma 0x000000000001dc00 irq 0 <6>ata2: SATA max UDMA/133 cmd 0xffffc2000273a580 ctl 0xffffc2000273a5a0 bmdma 0x000000000001dc08 irq 0 <6>ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <6>ata1.00: ata_hpa_resize 1: sectors = 781422768, hpa_sectors = 781422768 <6>ata1.00: ATA-7: SAMSUNG HD400LJ, ZZ100-14, max UDMA7 <6>ata1.00: 781422768 sectors, multi 16: LBA48 NCQ (depth 31/32) <6>ata1.00: ata_hpa_resize 1: sectors = 781422768, hpa_sectors = 781422768 <6>ata1.00: configured for UDMA/133 <6>ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <6>ata2.00: ata_hpa_resize 1: sectors = 781422768, hpa_sectors = 781422768 <6>ata2.00: ATA-7: SAMSUNG HD400LJ, ZZ100-14, max UDMA7 <6>ata2.00: 781422768 sectors, multi 16: LBA48 NCQ (depth 31/32) <6>ata2.00: ata_hpa_resize 1: sectors = 781422768, hpa_sectors = 781422768 <6>ata2.00: configured for UDMA/133 <5>scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD400LJ ZZ10 PQ: 0 ANSI: 5 <6>ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 <5>sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB) <5>sd 0:0:0:0: [sda] Write Protect is off <7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB) <5>sd 0:0:0:0: [sda] Write Protect is off <7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sda: sda1 sda2 <5>sd 0:0:0:0: [sda] Attached SCSI disk <5>scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD400LJ ZZ10 PQ: 0 ANSI: 5 <6>ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 <5>sd 1:0:0:0: [sdb] 781422768 512-byte hardware sectors (400088 MB) <5>sd 0:0:0:0: Attached scsi generic sg0 type 0 <5>sd 1:0:0:0: [sdb] Write Protect is off <7>sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 1:0:0:0: [sdb] 781422768 512-byte hardware sectors (400088 MB) <5>sd 1:0:0:0: [sdb] Write Protect is off <7>sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sdb: sdb1 sdb2 <5>sd 1:0:0:0: [sdb] Attached SCSI disk <5>sd 1:0:0:0: Attached scsi generic sg1 type 0 <4>ACPI: PCI Interrupt Link [LTIE] enabled at IRQ 21 <7>IOAPIC[0]: Set routing entry (4-21 -> 0x51 -> IRQ 21 Mode:1 Active:1) <6>ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LTIE] -> GSI 21 (level, low) -> IRQ 21 <5>sata_nv 0000:00:08.0: Using ADMA mode <7>PCI: Setting latency timer of device 0000:00:08.0 to 64 <6>scsi2 : sata_nv <6>scsi3 : sata_nv <6>ata3: SATA max UDMA/133 cmd 0xffffc2000273c480 ctl 0xffffc2000273c4a0 bmdma 0x000000000001c800 irq 0 <6>ata4: SATA max UDMA/133 cmd 0xffffc2000273c580 ctl 0xffffc2000273c5a0 bmdma 0x000000000001c808 irq 0 <6>ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <6>ata3.00: ata_hpa_resize 1: sectors = 781422768, hpa_sectors = 781422768 <6>ata3.00: ATA-7: SAMSUNG HD400LJ, ZZ100-14, max UDMA7 <6>ata3.00: 781422768 sectors, multi 16: LBA48 NCQ (depth 31/32) <6>ata3.00: ata_hpa_resize 1: sectors = 781422768, hpa_sectors = 781422768 <6>ata3.00: configured for UDMA/133 <6>ata4: SATA link down (SStatus 0 SControl 300) <5>scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD400LJ ZZ10 PQ: 0 ANSI: 5 <6>ata3: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 <5>sd 2:0:0:0: [sdc] 781422768 512-byte hardware sectors (400088 MB) <5>sd 2:0:0:0: [sdc] Write Protect is off <7>sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:0:0: [sdc] 781422768 512-byte hardware sectors (400088 MB) <5>sd 2:0:0:0: [sdc] Write Protect is off <7>sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sdc: sdc1 sdc2 <5>sd 2:0:0:0: [sdc] Attached SCSI disk <5>sd 2:0:0:0: Attached scsi generic sg2 type 0 <6>device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com <6>BIOS EDD facility v0.16 2004-Jun-25, 3 devices found <6>SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled <6>SGI XFS Quota Management subsystem <5>Filesystem "dm-3": Disabling barriers, not supported by the underlying device <5>XFS mounting filesystem dm-3 <7>Ending clean XFS mount for filesystem: dm-3 <6>parport_pc 00:07: reported by Plug and Play ACPI <6>parport0: PC-style at 0x378, irq 7 [PCSPP] <6>lp0: using parport0 (interrupt-driven). <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <6>i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00 <6>i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40 <7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver <4>ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20 <7>IOAPIC[0]: Set routing entry (4-20 -> 0x59 -> IRQ 20 Mode:1 Active:1) <6>ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 20 (level, low) -> IRQ 20 <7>PCI: Setting latency timer of device 0000:00:02.0 to 64 <6>ohci_hcd 0000:00:02.0: OHCI Host Controller <6>ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 <6>ohci_hcd 0000:00:02.0: irq 20, io mem 0xfe7fd000 <6>rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 <6>usb usb1: new device found, idVendor=0000, idProduct=0000 <6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 <4>rtc_cmos: probe of 00:02 failed with error -16 <6>usb usb1: Product: OHCI Host Controller <6>usb usb1: Manufacturer: Linux 2.6.22-rc4-49-default ohci_hcd <6>usb usb1: SerialNumber: 0000:00:02.0 <6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5 <6>usb usb1: configuration #1 chosen from 1 choice <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 10 ports detected <6>hdb: ATAPI 24X DVD-ROM drive, 256kB Cache, UDMA(66) <6>Uniform CD-ROM driver Revision: 3.20 <3>ck804xrom ck804xrom_init_one(): Unable to register resource 0x00000000ffc00000-0x00000000ffffffff - kernel bug? <4>ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22 <6>ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 22 (level, low) -> IRQ 22 <7>PCI: Setting latency timer of device 0000:00:02.1 to 64 <6>ehci_hcd 0000:00:02.1: EHCI Host Controller <6>ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 <6>ehci_hcd 0000:00:02.1: debug port 1 <7>PCI: cache line size of 64 is not supported by device 0000:00:02.1 <6>ehci_hcd 0000:00:02.1: irq 22, io mem 0xfe7e0000 <6>ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 <6>usb usb2: new device found, idVendor=0000, idProduct=0000 <7>CFI: Found no ck804xrom @ffc00000 device at location zero <6>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb2: Product: EHCI Host Controller <6>usb usb2: Manufacturer: Linux 2.6.22-rc4-49-default ehci_hcd <6>usb usb2: SerialNumber: 0000:00:02.1 <6>usb usb2: configuration #1 chosen from 1 choice <7>JEDEC: Found no ck804xrom @ffc00000 device at location zero <7>CFI: Found no ck804xrom @ffc00000 device at location zero <7>JEDEC: Found no ck804xrom @ffc00000 device at location zero <7>CFI: Found no ck804xrom @ffc00000 device at location zero <7>JEDEC: Found no ck804xrom @ffc00000 device at location zero <7>CFI: Found no ck804xrom @ffc10000 device at location zero <7>JEDEC: Found no ck804xrom @ffc10000 device at location zero <7>CFI: Found no ck804xrom @ffc10000 device at location zero <7>JEDEC: Found no ck804xrom @ffc10000 device at location zero <7>CFI: Found no ck804xrom @ffc10000 device at location zero <7>JEDEC: Found no ck804xrom @ffc10000 device at location zero <7>CFI: Found no ck804xrom @ffc20000 device at location zero <7>JEDEC: Found no ck804xrom @ffc20000 device at location zero <7>CFI: Found no ck804xrom @ffc20000 device at location zero <7>JEDEC: Found no ck804xrom @ffc20000 device at location zero <7>CFI: Found no ck804xrom @ffc20000 device at location zero <7>JEDEC: Found no ck804xrom @ffc20000 device at location zero <7>CFI: Found no ck804xrom @ffc30000 device at location zero <7>JEDEC: Found no ck804xrom @ffc30000 device at location zero <7>CFI: Found no ck804xrom @ffc30000 device at location zero <7>JEDEC: Found no ck804xrom @ffc30000 device at location zero <7>CFI: Found no ck804xrom @ffc30000 device at location zero <7>JEDEC: Found no ck804xrom @ffc30000 device at location zero <7>CFI: Found no ck804xrom @ffc40000 device at location zero <7>JEDEC: Found no ck804xrom @ffc40000 device at location zero <7>CFI: Found no ck804xrom @ffc40000 device at location zero <7>JEDEC: Found no ck804xrom @ffc40000 device at location zero <7>CFI: Found no ck804xrom @ffc40000 device at location zero <7>JEDEC: Found no ck804xrom @ffc40000 device at location zero <7>CFI: Found no ck804xrom @ffc50000 device at location zero <7>JEDEC: Found no ck804xrom @ffc50000 device at location zero <7>CFI: Found no ck804xrom @ffc50000 device at location zero <7>JEDEC: Found no ck804xrom @ffc50000 device at location zero <7>CFI: Found no ck804xrom @ffc50000 device at location zero <7>JEDEC: Found no ck804xrom @ffc50000 device at location zero <7>CFI: Found no ck804xrom @ffc60000 device at location zero <7>JEDEC: Found no ck804xrom @ffc60000 device at location zero <7>CFI: Found no ck804xrom @ffc60000 device at location zero <7>JEDEC: Found no ck804xrom @ffc60000 device at location zero <7>CFI: Found no ck804xrom @ffc60000 device at location zero <7>JEDEC: Found no ck804xrom @ffc60000 device at location zero <7>CFI: Found no ck804xrom @ffc70000 device at location zero <7>JEDEC: Found no ck804xrom @ffc70000 device at location zero <7>CFI: Found no ck804xrom @ffc70000 device at location zero <7>JEDEC: Found no ck804xrom @ffc70000 device at location zero <7>CFI: Found no ck804xrom @ffc70000 device at location zero <6>hub 2-0:1.0: USB hub found <7>JEDEC: Found no ck804xrom @ffc70000 device at location zero <7>CFI: Found no ck804xrom @ffc80000 device at location zero <7>JEDEC: Found no ck804xrom @ffc80000 device at location zero <7>CFI: Found no ck804xrom @ffc80000 device at location zero <7>JEDEC: Found no ck804xrom @ffc80000 device at location zero <7>CFI: Found no ck804xrom @ffc80000 device at location zero <7>JEDEC: Found no ck804xrom @ffc80000 device at location zero <7>CFI: Found no ck804xrom @ffc90000 device at location zero <7>JEDEC: Found no ck804xrom @ffc90000 device at location zero <7>CFI: Found no ck804xrom @ffc90000 device at location zero <7>JEDEC: Found no ck804xrom @ffc90000 device at location zero <7>CFI: Found no ck804xrom @ffc90000 device at location zero <7>JEDEC: Found no ck804xrom @ffc90000 device at location zero <7>CFI: Found no ck804xrom @ffca0000 device at location zero <7>JEDEC: Found no ck804xrom @ffca0000 device at location zero <7>CFI: Found no ck804xrom @ffca0000 device at location zero <7>JEDEC: Found no ck804xrom @ffca0000 device at location zero <7>CFI: Found no ck804xrom @ffca0000 device at location zero <7>JEDEC: Found no ck804xrom @ffca0000 device at location zero <7>CFI: Found no ck804xrom @ffcb0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcb0000 device at location zero <7>CFI: Found no ck804xrom @ffcb0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcb0000 device at location zero <7>CFI: Found no ck804xrom @ffcb0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcb0000 device at location zero <7>CFI: Found no ck804xrom @ffcc0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcc0000 device at location zero <7>CFI: Found no ck804xrom @ffcc0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcc0000 device at location zero <7>CFI: Found no ck804xrom @ffcc0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcc0000 device at location zero <7>CFI: Found no ck804xrom @ffcd0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcd0000 device at location zero <7>CFI: Found no ck804xrom @ffcd0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcd0000 device at location zero <7>CFI: Found no ck804xrom @ffcd0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcd0000 device at location zero <7>CFI: Found no ck804xrom @ffce0000 device at location zero <7>JEDEC: Found no ck804xrom @ffce0000 device at location zero <7>CFI: Found no ck804xrom @ffce0000 device at location zero <7>JEDEC: Found no ck804xrom @ffce0000 device at location zero <7>CFI: Found no ck804xrom @ffce0000 device at location zero <7>JEDEC: Found no ck804xrom @ffce0000 device at location zero <7>CFI: Found no ck804xrom @ffcf0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcf0000 device at location zero <7>CFI: Found no ck804xrom @ffcf0000 device at location zero <6>hub 2-0:1.0: 10 ports detected <7>JEDEC: Found no ck804xrom @ffcf0000 device at location zero <7>CFI: Found no ck804xrom @ffcf0000 device at location zero <7>JEDEC: Found no ck804xrom @ffcf0000 device at location zero <7>CFI: Found no ck804xrom @ffd00000 device at location zero <7>JEDEC: Found no ck804xrom @ffd00000 device at location zero <7>CFI: Found no ck804xrom @ffd00000 device at location zero <7>JEDEC: Found no ck804xrom @ffd00000 device at location zero <7>CFI: Found no ck804xrom @ffd00000 device at location zero <7>JEDEC: Found no ck804xrom @ffd00000 device at location zero <7>CFI: Found no ck804xrom @ffd10000 device at location zero <7>JEDEC: Found no ck804xrom @ffd10000 device at location zero <7>CFI: Found no ck804xrom @ffd10000 device at location zero <7>JEDEC: Found no ck804xrom @ffd10000 device at location zero <7>CFI: Found no ck804xrom @ffd10000 device at location zero <7>JEDEC: Found no ck804xrom @ffd10000 device at location zero <7>CFI: Found no ck804xrom @ffd20000 device at location zero <7>JEDEC: Found no ck804xrom @ffd20000 device at location zero <7>CFI: Found no ck804xrom @ffd20000 device at location zero <7>JEDEC: Found no ck804xrom @ffd20000 device at location zero <7>CFI: Found no ck804xrom @ffd20000 device at location zero <7>JEDEC: Found no ck804xrom @ffd20000 device at location zero <7>CFI: Found no ck804xrom @ffd30000 device at location zero <7>JEDEC: Found no ck804xrom @ffd30000 device at location zero <7>CFI: Found no ck804xrom @ffd30000 device at location zero <7>JEDEC: Found no ck804xrom @ffd30000 device at location zero <7>CFI: Found no ck804xrom @ffd30000 device at location zero <7>JEDEC: Found no ck804xrom @ffd30000 device at location zero <7>CFI: Found no ck804xrom @ffd40000 device at location zero <7>JEDEC: Found no ck804xrom @ffd40000 device at location zero <7>CFI: Found no ck804xrom @ffd40000 device at location zero <7>JEDEC: Found no ck804xrom @ffd40000 device at location zero <7>CFI: Found no ck804xrom @ffd40000 device at location zero <7>JEDEC: Found no ck804xrom @ffd40000 device at location zero <7>CFI: Found no ck804xrom @ffd50000 device at location zero <7>JEDEC: Found no ck804xrom @ffd50000 device at location zero <7>CFI: Found no ck804xrom @ffd50000 device at location zero <7>JEDEC: Found no ck804xrom @ffd50000 device at location zero <7>CFI: Found no ck804xrom @ffd50000 device at location zero <7>JEDEC: Found no ck804xrom @ffd50000 device at location zero <7>CFI: Found no ck804xrom @ffd60000 device at location zero <7>JEDEC: Found no ck804xrom @ffd60000 device at location zero <7>CFI: Found no ck804xrom @ffd60000 device at location zero <7>JEDEC: Found no ck804xrom @ffd60000 device at location zero <7>CFI: Found no ck804xrom @ffd60000 device at location zero <7>JEDEC: Found no ck804xrom @ffd60000 device at location zero <7>CFI: Found no ck804xrom @ffd70000 device at location zero <7>JEDEC: Found no ck804xrom @ffd70000 device at location zero <7>CFI: Found no ck804xrom @ffd70000 device at location zero <7>JEDEC: Found no ck804xrom @ffd70000 device at location zero <7>CFI: Found no ck804xrom @ffd70000 device at location zero <7>JEDEC: Found no ck804xrom @ffd70000 device at location zero <7>CFI: Found no ck804xrom @ffd80000 device at location zero <7>JEDEC: Found no ck804xrom @ffd80000 device at location zero <7>CFI: Found no ck804xrom @ffd80000 device at location zero <7>JEDEC: Found no ck804xrom @ffd80000 device at location zero <7>CFI: Found no ck804xrom @ffd80000 device at location zero <7>JEDEC: Found no ck804xrom @ffd80000 device at location zero <7>CFI: Found no ck804xrom @ffd90000 device at location zero <7>JEDEC: Found no ck804xrom @ffd90000 device at location zero <7>CFI: Found no ck804xrom @ffd90000 device at location zero <7>JEDEC: Found no ck804xrom @ffd90000 device at location zero <7>CFI: Found no ck804xrom @ffd90000 device at location zero <7>JEDEC: Found no ck804xrom @ffd90000 device at location zero <7>CFI: Found no ck804xrom @ffda0000 device at location zero <7>JEDEC: Found no ck804xrom @ffda0000 device at location zero <7>CFI: Found no ck804xrom @ffda0000 device at location zero <7>JEDEC: Found no ck804xrom @ffda0000 device at location zero <7>CFI: Found no ck804xrom @ffda0000 device at location zero <7>JEDEC: Found no ck804xrom @ffda0000 device at location zero <7>CFI: Found no ck804xrom @ffdb0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdb0000 device at location zero <7>CFI: Found no ck804xrom @ffdb0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdb0000 device at location zero <7>CFI: Found no ck804xrom @ffdb0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdb0000 device at location zero <7>CFI: Found no ck804xrom @ffdc0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdc0000 device at location zero <7>CFI: Found no ck804xrom @ffdc0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdc0000 device at location zero <7>CFI: Found no ck804xrom @ffdc0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdc0000 device at location zero <7>CFI: Found no ck804xrom @ffdd0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdd0000 device at location zero <7>CFI: Found no ck804xrom @ffdd0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdd0000 device at location zero <7>CFI: Found no ck804xrom @ffdd0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdd0000 device at location zero <7>CFI: Found no ck804xrom @ffde0000 device at location zero <7>JEDEC: Found no ck804xrom @ffde0000 device at location zero <7>CFI: Found no ck804xrom @ffde0000 device at location zero <7>JEDEC: Found no ck804xrom @ffde0000 device at location zero <7>CFI: Found no ck804xrom @ffde0000 device at location zero <7>JEDEC: Found no ck804xrom @ffde0000 device at location zero <7>CFI: Found no ck804xrom @ffdf0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdf0000 device at location zero <7>CFI: Found no ck804xrom @ffdf0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdf0000 device at location zero <7>CFI: Found no ck804xrom @ffdf0000 device at location zero <7>JEDEC: Found no ck804xrom @ffdf0000 device at location zero <7>CFI: Found no ck804xrom @ffe00000 device at location zero <7>JEDEC: Found no ck804xrom @ffe00000 device at location zero <7>CFI: Found no ck804xrom @ffe00000 device at location zero <7>JEDEC: Found no ck804xrom @ffe00000 device at location zero <7>CFI: Found no ck804xrom @ffe00000 device at location zero <7>JEDEC: Found no ck804xrom @ffe00000 device at location zero <7>CFI: Found no ck804xrom @ffe10000 device at location zero <7>JEDEC: Found no ck804xrom @ffe10000 device at location zero <7>CFI: Found no ck804xrom @ffe10000 device at location zero <7>JEDEC: Found no ck804xrom @ffe10000 device at location zero <7>CFI: Found no ck804xrom @ffe10000 device at location zero <7>JEDEC: Found no ck804xrom @ffe10000 device at location zero <7>CFI: Found no ck804xrom @ffe20000 device at location zero <7>JEDEC: Found no ck804xrom @ffe20000 device at location zero <7>CFI: Found no ck804xrom @ffe20000 device at location zero <7>JEDEC: Found no ck804xrom @ffe20000 device at location zero <7>CFI: Found no ck804xrom @ffe20000 device at location zero <7>JEDEC: Found no ck804xrom @ffe20000 device at location zero <7>CFI: Found no ck804xrom @ffe30000 device at location zero <7>JEDEC: Found no ck804xrom @ffe30000 device at location zero <7>CFI: Found no ck804xrom @ffe30000 device at location zero <7>JEDEC: Found no ck804xrom @ffe30000 device at location zero <7>CFI: Found no ck804xrom @ffe30000 device at location zero <7>JEDEC: Found no ck804xrom @ffe30000 device at location zero <7>CFI: Found no ck804xrom @ffe40000 device at location zero <7>JEDEC: Found no ck804xrom @ffe40000 device at location zero <7>CFI: Found no ck804xrom @ffe40000 device at location zero <7>JEDEC: Found no ck804xrom @ffe40000 device at location zero <7>CFI: Found no ck804xrom @ffe40000 device at location zero <7>JEDEC: Found no ck804xrom @ffe40000 device at location zero <7>CFI: Found no ck804xrom @ffe50000 device at location zero <7>JEDEC: Found no ck804xrom @ffe50000 device at location zero <7>CFI: Found no ck804xrom @ffe50000 device at location zero <7>JEDEC: Found no ck804xrom @ffe50000 device at location zero <7>CFI: Found no ck804xrom @ffe50000 device at location zero <7>JEDEC: Found no ck804xrom @ffe50000 device at location zero <7>CFI: Found no ck804xrom @ffe60000 device at location zero <7>JEDEC: Found no ck804xrom @ffe60000 device at location zero <7>CFI: Found no ck804xrom @ffe60000 device at location zero <7>JEDEC: Found no ck804xrom @ffe60000 device at location zero <7>CFI: Found no ck804xrom @ffe60000 device at location zero <7>JEDEC: Found no ck804xrom @ffe60000 device at location zero <7>CFI: Found no ck804xrom @ffe70000 device at location zero <7>JEDEC: Found no ck804xrom @ffe70000 device at location zero <7>CFI: Found no ck804xrom @ffe70000 device at location zero <7>JEDEC: Found no ck804xrom @ffe70000 device at location zero <7>CFI: Found no ck804xrom @ffe70000 device at location zero <7>JEDEC: Found no ck804xrom @ffe70000 device at location zero <7>CFI: Found no ck804xrom @ffe80000 device at location zero <7>JEDEC: Found no ck804xrom @ffe80000 device at location zero <7>CFI: Found no ck804xrom @ffe80000 device at location zero <7>JEDEC: Found no ck804xrom @ffe80000 device at location zero <7>CFI: Found no ck804xrom @ffe80000 device at location zero <7>JEDEC: Found no ck804xrom @ffe80000 device at location zero <7>CFI: Found no ck804xrom @ffe90000 device at location zero <7>JEDEC: Found no ck804xrom @ffe90000 device at location zero <7>CFI: Found no ck804xrom @ffe90000 device at location zero <7>JEDEC: Found no ck804xrom @ffe90000 device at location zero <7>CFI: Found no ck804xrom @ffe90000 device at location zero <7>JEDEC: Found no ck804xrom @ffe90000 device at location zero <7>CFI: Found no ck804xrom @ffea0000 device at location zero <7>JEDEC: Found no ck804xrom @ffea0000 device at location zero <7>CFI: Found no ck804xrom @ffea0000 device at location zero <7>JEDEC: Found no ck804xrom @ffea0000 device at location zero <7>CFI: Found no ck804xrom @ffea0000 device at location zero <7>JEDEC: Found no ck804xrom @ffea0000 device at location zero <7>CFI: Found no ck804xrom @ffeb0000 device at location zero <7>JEDEC: Found no ck804xrom @ffeb0000 device at location zero <7>CFI: Found no ck804xrom @ffeb0000 device at location zero <7>JEDEC: Found no ck804xrom @ffeb0000 device at location zero <7>CFI: Found no ck804xrom @ffeb0000 device at location zero <7>JEDEC: Found no ck804xrom @ffeb0000 device at location zero <7>CFI: Found no ck804xrom @ffec0000 device at location zero <7>JEDEC: Found no ck804xrom @ffec0000 device at location zero <7>CFI: Found no ck804xrom @ffec0000 device at location zero <7>JEDEC: Found no ck804xrom @ffec0000 device at location zero <7>CFI: Found no ck804xrom @ffec0000 device at location zero <7>JEDEC: Found no ck804xrom @ffec0000 device at location zero <7>CFI: Found no ck804xrom @ffed0000 device at location zero <7>JEDEC: Found no ck804xrom @ffed0000 device at location zero <7>CFI: Found no ck804xrom @ffed0000 device at location zero <7>JEDEC: Found no ck804xrom @ffed0000 device at location zero <7>CFI: Found no ck804xrom @ffed0000 device at location zero <7>JEDEC: Found no ck804xrom @ffed0000 device at location zero <7>CFI: Found no ck804xrom @ffee0000 device at location zero <7>JEDEC: Found no ck804xrom @ffee0000 device at location zero <7>CFI: Found no ck804xrom @ffee0000 device at location zero <7>JEDEC: Found no ck804xrom @ffee0000 device at location zero <7>CFI: Found no ck804xrom @ffee0000 device at location zero <7>JEDEC: Found no ck804xrom @ffee0000 device at location zero <7>CFI: Found no ck804xrom @ffef0000 device at location zero <7>JEDEC: Found no ck804xrom @ffef0000 device at location zero <7>CFI: Found no ck804xrom @ffef0000 device at location zero <7>JEDEC: Found no ck804xrom @ffef0000 device at location zero <7>CFI: Found no ck804xrom @ffef0000 device at location zero <7>JEDEC: Found no ck804xrom @ffef0000 device at location zero <7>CFI: Found no ck804xrom @fff00000 device at location zero <7>JEDEC: Found no ck804xrom @fff00000 device at location zero <7>CFI: Found no ck804xrom @fff00000 device at location zero <7>JEDEC: Found no ck804xrom @fff00000 device at location zero <7>CFI: Found no ck804xrom @fff00000 device at location zero <4>Found: SST 49LF080A <6>ck804xrom @fff00000: Found 1 x8 devices at 0x0 in 8-bit bank <5>number of JEDEC chips: 1 <5>cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. <6>shpchp: HPC vendor_id 1022 device_id 7458 ss_vid 0 ss_did 0 <3>shpchp: shpc_init: cannot reserve MMIO region <6>shpchp: HPC vendor_id 1022 device_id 7458 ss_vid 0 ss_did 0 <3>shpchp: shpc_init: cannot reserve MMIO region <6>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 <6>Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI <6>Copyright (c) 1999-2006 Intel Corporation. <7>IOAPIC[2]: Set routing entry (10-0 -> 0x61 -> IRQ 47 Mode:1 Active:1) <6>ACPI: PCI Interrupt 0000:05:03.0[A] -> GSI 47 (level, low) -> IRQ 47 <6>usb 1-2: new low speed USB device using ohci_hcd and address 2 <6>usb 1-2: new device found, idVendor=413c, idProduct=3010 <6>usb 1-2: new device strings: Mfr=0, Product=0, SerialNumber=0 <6>e1000: 0000:05:03.0: e1000_probe: (PCI-X:133MHz:64-bit) 00:30:48:57:6e:02 <6>usb 1-2: configuration #1 chosen from 1 choice <6>e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection <7>IOAPIC[2]: Set routing entry (10-1 -> 0x69 -> IRQ 48 Mode:1 Active:1) <6>ACPI: PCI Interrupt 0000:05:03.1[B] -> GSI 48 (level, low) -> IRQ 48 <6>e1000: 0000:05:03.1: e1000_probe: (PCI-X:133MHz:64-bit) 00:30:48:57:6e:03 <6>usbcore: registered new interface driver hiddev <6>e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection <6>input: HID 413c:3010 as /class/input/input2 <6>input: USB HID v1.00 Mouse [HID 413c:3010] on usb-0000:00:02.0-2 <6>usbcore: registered new interface driver usbhid <6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver <6>Adding 157286392k swap on /dev/vg_system/swap. Priority:-1 extents:1 across:157286392k <5>Filesystem "dm-3": Disabling barriers, not supported by the underlying device <6>loop: module loaded <5>XFS mounting filesystem sda1 <7>Ending clean XFS mount for filesystem: sda1 <5>XFS mounting filesystem sdb1 <7>Ending clean XFS mount for filesystem: sdb1 <5>XFS mounting filesystem sdc1 <7>Ending clean XFS mount for filesystem: sdc1 <5>Filesystem "dm-0": Disabling barriers, not supported by the underlying device <5>XFS mounting filesystem dm-0 <7>Ending clean XFS mount for filesystem: dm-0 <5>Filesystem "dm-1": Disabling barriers, not supported by the underlying device <5>XFS mounting filesystem dm-1 <7>Ending clean XFS mount for filesystem: dm-1 <5>Filesystem "dm-2": Disabling barriers, not supported by the underlying device <5>XFS mounting filesystem dm-2 <7>Ending clean XFS mount for filesystem: dm-2 <5>Filesystem "dm-5": Disabling barriers, not supported by the underlying device <5>XFS mounting filesystem dm-5 <7>Ending clean XFS mount for filesystem: dm-5 Kernel logging (ksyslog) stopped. Kernel log daemon terminating. Boot logging started on /dev/tty1(/dev/console) at Wed Jun 27 14:46:55 2007 Trying manual resume from /dev/vg_system/swap Creating device nodes with udev Loading ide-core Loading ide-disk Loading scsi_mod Loading sd_mod Loading processor Loading thermal Loading amd74xx Loading libata Loading sata_nv Loading fan Loading dm-mod Loading edd Loading dm-snapshot Waiting for /dev/mapper/control to appear: ok Loading xfs resume device /dev/vg_system/swap not found (ignoring) 6 logical volume(s) in volume group "vg_system" now active Waiting for device /dev/vg_system/root to appear: ok fsck 1.39 (29-May-2006) [/bin/fsck.xfs (1) -- /] fsck.xfs -a /dev/vg_system/root /bin/fsck.xfs: XFS file system. fsck succeeded. Mounting root device read-write. Mounting root /dev/vg_system/root Boot logging started on /dev/tty1(/dev/console (deleted)) at Thu Jun 28 00:47:04 2007 boot.udev start Starting udevd done 'boot.udev start' exits with status 0 boot.rootfsck start Activating swap-devices in /etc/fstab... done'boot.rootfsck start' exits with status 0 boot.loadmodules start Loading required kernel modules done'boot.loadmodules start' exits with status 0 boot.preload_early start done 'boot.preload_early start' exits with status 0 boot.device-mapper start Activating device mapper... done 'boot.device-mapper start' exits with status 0 boot.md start Starting MD Raid done 'boot.md start' exits with status 0 boot.lvm start Waiting for udev to settle... Scanning for LVM volume groups... Reading all physical volumes. This may take a while... Found volume group "vg_system" using metadata type lvm2 Activating LVM volume groups... 6 logical volume(s) in volume group "vg_system" now active done 'boot.lvm start' exits with status 0 boot.localfs start Checking file systems... fsck 1.39 (29-May-2006) /sbin/fsck.xfs: XFS file system. /sbin/fsck.xfs: XFS file system. /sbin/fsck.xfs: XFS file system. /sbin/fsck.xfs: XFS file system. /sbin/fsck.xfs: XFS file system. /sbin/fsck.xfs: XFS file system. /sbin/fsck.xfs: XFS file system. donedone Mounting local file systems... proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) debugfs on /sys/kernel/debug type debugfs (rw) udev on /dev type tmpfs (rw) devpts on /dev/pts type devpts (rw,mode=0620,gid=5) /dev/sda1 on /boot type xfs (rw) /dev/sdb1 on /boot_bak1 type xfs (rw) /dev/sdc1 on /boot_bak2 type xfs (rw) /dev/mapper/vg_system-data on /data type xfs (rw) /dev/mapper/vg_system-home on /home type xfs (rw) /dev/mapper/vg_system-opt on /opt type xfs (rw) /dev/mapper/vg_system-tmp on /tmp type xfs (rw) done'boot.localfs start' exits with status 0 boot.cleanup start 'boot.cleanup start' exits with status 0 boot.clock start Setting up the hardware clockdone 'boot.clock start' exits with status 0 boot.klog start Creating /var/log/boot.msg donekillproc: kill(1153,29) 'boot.klog start' exits with status 0 boot.proc start 'boot.proc start' exits with status 0 boot.scpm start 'boot.scpm start' exits with status 0 boot.sysctl start Setting current sysctl status from /etc/sysctl.conf net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.rp_filter = 1 done 'boot.sysctl start' exits with status 0 boot.udev_retry start 'boot.udev_retry start' exits with status 0 boot.videobios start 'boot.videobios start' exits with status 0 boot.crypto start 'boot.crypto start' exits with status 0 boot.ipconfig start Enabling syn flood protectiondone Enabling IP forwardingdone done 'boot.ipconfig start' exits with status 0 boot.localnet start Setting up hostname 'frontend'done Setting up loopback interface lo lo IP address: 127.0.0.1/8 done 'boot.localnet start' exits with status 0 boot.preload start done 'boot.preload start' exits with status 0 boot.swap start Activating remaining swap-devices in /etc/fstab... done'boot.swap start' exits with status 0 SuSEfirewall2_init start Starting Firewall Initialization (phase 1 of 2) SuSEfirewall2: Warning: ip6tables does not support state matching. Extended IPv6 support disabled. done 'SuSEfirewall2_init start' exits with status 0 boot.ldconfig start 'boot.ldconfig start' exits with status 0 System Boot Control: The system has been set up System Boot Control: Running /etc/init.d/boot.local donekillproc: kill(1153,3) INIT: Entering runlevel: 5 Boot logging started on /dev/tty1(/dev/console) at Wed Jun 27 14:47:21 2007 Master Resource Control: previous runlevel: N, switching to runlevel: 5 startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/sbin/resmgrd ] done Initializing random number generatordone startproc: execve (/usr/bin/dbus-daemon) [ /usr/bin/dbus-daemon --system ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/bin/dbus-daemon ] startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng -a /var/lib/dhcp/dev/log -a /var/lib/named/dev/log ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PWD=/ PREVLEVEL=N LINES=44 SHLVL=2 HOME=/ SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/sbin/syslog-ng ] startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/sbin/acpid ] startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PWD=/ PREVLEVEL=N LINES=44 SHLVL=2 HOME=/ SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/sbin/klogd ] acpid: loading ACPI modules ( ac battery button ) done acpid: will not skip unsupported modules acpid: loading ACPI laptop modules ( ) done Starting acpid done startproc: execve (/usr/sbin/irqbalance) [ /usr/sbin/irqbalance ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/irqbalance ] Starting syslog servicesdone Starting irqbalance done Starting resource managerdone Starting D-Bus daemondone startproc: execve (/usr/sbin/polkitd) [ /usr/sbin/polkitd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/polkitd ] Loading up bashrc to get latest mod-tools. Loading the 2.6.x pvfs2 module insmod: error inserting '/lib/modules/2.6.22-rc4-49-default/kernel/fs/pvfs2/pvfs2.ko': -1 Unknown symbol in module Starting pvfs2-client Mounting 2.6.x pvfs2 on /mnt/pvfs2 FATAL: Module pvfs2 not found. Usage: mount -V : print version mount -h : print this help mount : list mounted filesystems mount -l : idem, including volume labels So far the informational part. Next the mounting. The command is `mount [-t fstype] something somewhere'. Details found in /etc/fstab may be omitted. mount -a [-t|-O] ... : mount all stuff from /etc/fstab mount device : mount device at the known place mount directory : mount known device here mount -t type dev dir : ordinary mount command Note that one does not really mount a device, one mounts a filesystem (of the given type) found on the device. One can also mount an already visible directory tree elsewhere: mount --bind olddir newdir or move a subtree: mount --move olddir newdir A device can be given by name, say /dev/hda1 or /dev/cdrom, or by label, using -L label or by uuid, using -U uuid . Other options: [-nfFrsvw] [-o options] [-p passwdfd]. For many more details, say man 8 mount . PVFS2 mount details: Mounting PVFS2 Filesystem: mkdir: missing operand Try `mkdir --help' for more information. done Starting PolicyKit daemondone startproc: execve (/usr/sbin/hald) [ /usr/sbin/hald --daemon=yes ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/hald ] Loading keymap i386/qwerty/us.map.gz doneLoading compose table winkeys shiftctrl latin1.adddone Start Unicode mode doneLoading console font lat9w-16.psfu -m trivial G0:loadable doneStarting HAL daemondone Loading CPUFreq modulesdone killproc: kill(3196,20) killproc: kill(3148,1) killproc: kill(3196,18) killproc: kill(3196,12) startproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PWD=/ LANG=en_US.UTF-8 PREVLEVEL=N LINES=44 QT_SYSTEM_DIR=/usr/share/desktop-data SHLVL=2 HOME=/ XCURSOR_THEME=crystalwhite WINDOWMANAGER=/usr/bin/kde SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ] Starting service kdmdone Setting up network interfaces: lo lo IP address: 127.0.0.1/8 done eth0 device: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) eth0 configuration: eth-id-00:30:48:57:6e:02 eth0 (DHCP) . IP/Netmask: 192.168.1.5 / 255.255.255.0 done eth1 device: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) eth1 configuration: eth-id-00:30:48:57:6e:03 eth1 IP address: 192.168.0.10/24 doneSetting up service network . . . . . . . . . . . . . . . .done startproc: execve (/usr/sbin/nmbd) [ /usr/sbin/nmbd -D -s /etc/samba/smb.conf ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/nmbd ] startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/sbin/portmap ] startproc: execve (/sbin/auditd) [ /sbin/auditd -n ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/sbin/auditd ] Starting RPC portmap daemondone Starting nfsboot (sm-notify) done Importing Net File System (NFS)mount server reported tcp not available, falling back to udp mount: RPC: Program not registered done Starting Samba NMB daemon done Checking/updating CPU microcode unused startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/sshd ] checkproc: /opt/kde3/bin/kdm 4032 Starting auditd done startproc: execve (/usr/sbin/knockd) [ /usr/sbin/knockd -d ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/knockd ] Starting SSH daemondone Starting knockd done startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -f /var/run/acpid.socket -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ] Starting powersaved: done Starting name server BIND startproc: execve (/usr/sbin/named) [ /usr/sbin/named -t /var/lib/named -u named ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/sbin:/usr/sbin:/bin:/usr/bin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 checkAndCopyConfigFilesCalled=yes HOME=/ SHLVL=2 namedConfChecked=yes SPLASH=yes initializeNamedCalled=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/named ] done startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/usr/bin/ionice DAEMON=/usr/sbin/cupsd ] startproc: execve (/opt/pvfs2/sbin/pvfs2-server) [ /opt/pvfs2/sbin/pvfs2-server --pidfile /var/run/pvfs2.pid /etc/pvfs2-fs.conf /etc/pvfs2-server.conf-frontend ], [ PVFS2BIN=/opt/pvfs2/sbin PVFS2CLIENTCORE=/opt/pvfs2/sbin/pvfs2-client-core CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 PVFS2_FS_CONF=/etc/pvfs2-fs.conf PVFS_PROTOCOL=tcp PVFS_PORT=3334 PVFS2_CONF_PATH=/etc LC_ALL=POSIX PVFS2_SERVER_CONF=/etc/pvfs2-server.conf-frontend INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin PVFS_METADATA_CONN_DESC=tcp://192.168.0.10:3334/pvfs2-fs vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PVFS2CLIENT=/opt/pvfs2/sbin/pvfs2-client PVFS_MOUNTPOINT=/mnt/pvfs2 PREVLEVEL=N LINES=44 PVFS_METADATA_SERVER=192.168.0.10 HOME=/ SHLVL=2 PVFS2SERVER=/opt/pvfs2/sbin/pvfs2-server SPLASH=yes PVFS2_PIDFILE=/var/run/pvfs2.pid ROOTFS_BLKDEV=/dev/vg_system/root PVFS_PATH=/opt/pvfs2 _=/sbin/startproc DAEMON=/opt/pvfs2/sbin/pvfs2-server ] Starting cupsddone Starting PVFS2 server: touch /var/lock/subsys/pvfs2-server done startproc: execve (/usr/sbin/smbd) [ /usr/sbin/smbd -D -s /etc/samba/smb.conf ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 TMPDIR=/var/tmp LC_ALL= INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg LANG=en_US.UTF-8 PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 LC_CTYPE= SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/smbd ] [D 14:47:26.548122] PVFS2 Server version 2.6.3 starting. Starting Samba SMB daemon done Mount CIFS File Systems unused startproc: execve (/usr/sbin/rpc.mountd) [ /usr/sbin/rpc.mountd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/rpc.mountd ] Starting kernel based NFS serverexportfs: /etc/exports [1]: Neither 'subtree_check' or 'no_subtree_check' specified for export "*.ccaconsulting.com:/data/export/". Assuming default behaviour ('subtree_check'). NOTE: this default will change with nfs-utils version 1.1.0 exportfs: /etc/exports [1]: Neither 'subtree_check' or 'no_subtree_check' specified for export "192.168.0.1/255.255.0.0:/data/export". Assuming default behaviour ('subtree_check'). NOTE: this default will change with nfs-utils version 1.1.0 done Try to get initial date and time via NTP from au.pool.ntp.org 0.au.pool.ntp.org 1.au.pool.ntp.org 3.au.pool.ntp.orgcheckproc: /opt/kde3/bin/kdm 4032 done Starting network time protocol daemon (NTPD)startproc: execve (/usr/sbin/ntpd) [ /usr/sbin/ntpd -p /var/lib/ntp/var/run/ntp/ntpd.pid -u ntp -i /var/lib/ntp ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/ntpd ] done startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/nscd ] Starting Name Service Cache Daemondone xend unused xendomains unused Starting DHCP server [chroot]done Starting mail service (Postfix)done Starting CRON daemonstartproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=xfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PREVLEVEL=N LINES=44 HOME=/ SHLVL=2 SPLASH=yes ROOTFS_BLKDEV=/dev/vg_system/root _=/sbin/startproc DAEMON=/usr/sbin/cron ] done Starting Firewall Initialization (phase 2 of 2) done Master Resource Control: runlevel 5 has been reached Skipped services in runlevel 5: microcode smbfs xend xendomains killproc: kill(3033,3)